Manifold Ensign Soil Short 150mm

Code article :

Description

The ENSIGN SOIL cast iron multi-connectors, save space by grouping waste pipes from various sources. The space is saved by allowing the grouping of evacuations of small diameter pipework from various devices such as sinks, basins, bidets, urinals or showers on a single point just above the floor level. The waste pipe connections must be designed in such a way as to avoid any risk of siphoning.

The multi-connector DN100 allows the push-fit connection of three plastic or copper tube entries of external diameters (DE) 36 and / or DE 42. The DN150 allows th  push-fit connection of three plastic or copper tube entries of external diameters (DE) 54 and / or DE 56.

Installation instructions

  1. The cut the appropriate groove shown on the rubber connection grommets.
  2. Remove the grommet and tear out the centre disk
  3. Apply a small amount of silicone grease to the outside of the grommet and re-fit into the manifold ensuring that the retaining of the grommet is located correctly in the casing.
  4. Lubricate the pipe end and insert into the grommet with a rotational movement. Chamfering the waste pipe will ease the insertion.
  5. Any grommet not fitted with a waste pipe must also be removed any applied point 3.

Technical infos & product description

Product description

The ENSIGN SOIL cast iron multi-connectors, save space by grouping waste pipes from various sources. The space is saved by allowing the grouping of evacuations of small diameter pipework from various devices such as sinks, basins, bidets, urinals or showers on a single point just above the floor level. The waste pipe connections must be designed in such a way as to avoid any risk of siphoning.

The multi-connector DN100 allows the push-fit connection of three plastic or copper tube entries of external diameters (DE) 36 and / or DE 42. The DN150 allows th  push-fit connection of three plastic or copper tube entries of external diameters (DE) 54 and / or DE 56.

Installation instructions

  1. The cut the appropriate groove shown on the rubber connection grommets.
  2. Remove the grommet and tear out the centre disk
  3. Apply a small amount of silicone grease to the outside of the grommet and re-fit into the manifold ensuring that the retaining of the grommet is located correctly in the casing.
  4. Lubricate the pipe end and insert into the grommet with a rotational movement. Chamfering the waste pipe will ease the insertion.
  5. Any grommet not fitted with a waste pipe must also be removed any applied point 3.

Recommended use :

  • Soil and drain
  • Intensive Use
  • Aggressive effluents
  • Standard Use
  • Domestic use
  • Rainwater

Major benefits :

  • Performances guaranteed with marks delivered by third party.
  • Long lasting operational safety thanks to the robustness and stiffness (around 700kN.m) of cast iron and usage of flexible mechanical couplings.
  • High level of fire safety with the excellent fire resistance up to 240 minutes according to configuration (mostly requires no special fire protection saving time and cost).
  • Best acoustic comfort.
  • Easiness of installation due to mechanical couplings assembled with simple tools.

Technical infos

  • Hot water resistance : 24h at 95°C.
  • Thermal cycle resistance: 1500 cycles between 15°C and 93°C.
  • Chemical resistance for 2 ≤ pH ≤ 13, up to 80°C.
  • Salt spray resistance : 1500h.

Coating description :

  • External coating : Red-brown, anti-corrosive acrylic primer paint, average dry film thickness 40 μm.

  • Internal coating : Two-component ochre colored epoxy coating, average dry film thickness of 130 μm.

  • Material :
  • Industry product standards :
  • Range Fire Classification : A1
  • Acoustic Performance : Lsc ≤ 5dB(A) according to EN 14366
  • Percentage of Recycled Content : 97%
  • Recycling Information : 97%